 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| TECHNICAL DATA Telephone Tone Ringer with Bridge Diode The IL6840 is a monolithic integrated circuit telephone tone ringer with bridge diode, when coupled with an appropriate transducer, it replaces the electro-mechanical bell. The device is designed for use with either a piezo transducer or an inexpensive transformer coupled speaker to produce a pleasing tone composed of a high frequency (fR) alternating with a low frequency (fL) resulting in a warble frequency. The supply voltage is obtained from the AC ring signal and the circuit is designed so that noise on the line or variation of the ringing signal can not affect correct operation of the device. * On chip high voltage full wave diode bridge rectifier * Low current consumption, in order to allow the parallel operation of the 4 devices * Low external component count * Tone and switching frequencies adjustable by external components * High noise immunity due to built-in voltage-current hysteresis * Activation voltage adjustable * Internal zener diodes to protect against over voltages * Ringer impedance adjustable with external components IL6840 ORDERING INFORMATION IL6840N Plastic DIP IL6840D SOIC TA = -40 to 70 C for package PIN ASSIGNMENT OUT BLOCK DIAGRAM 1 IL6840 MAXIMUM RATINGS* (TA = 25C) Symbol VTP VTP ICC Tstg * Parameter Calling Voltage (f = 50 Hz) Continuous Calling Voltage (f = 50 Hz) 5 Sec ON/10 Sec OFF Supply Current Storage and Junction Temperature Value 120 200 22 -60 to +125 Unit Vrms Vrms mA C Maximum Ratings are those values beyond which damage to the device may occur. Functional operation should be restricted to the Recommended Operating Conditions. RECOMMENDED OPERATING CONDITIONS Symbol VCC TA Supply Voltage Operating Temperature -40 Parameter Min Max 26 +70 Unit V C This device contains protection circuitry to guard against damage due to high static voltages or electric fields. However, precautions must be taken to avoid applications of any voltage higher than maximum rated voltages to this high-impedance circuit. For proper operation, VIN and VOUT should be constrained to the range GND(VIN or VOUT)VCC. Unused inputs must always be tied to an appropriate logic voltage level (e.g., either GND or VCC). Unused outputs must be left open. ELECTRICAL CHARACTERISTICS (TA = 25C) Symbol ICC VON VONR VSUS RD VOUT Parameter Current Consumption without Load Activiation Voltage Activiation Voltage Range Sustaining Voltage Differential Resistance in Off Condition Output Voltage Swing VTIP = 8.0 V VRING = 0 V VS = 26 V, VSRC = 8.0 V, VOFR = 8.0 V VS = 26 V RA = 1 K Test Conditions VS=8.8 to 26 V 12.2 8 8 6.4 21 Guaranteed Limits Min Max 1.8 13 10 8.8 3500 25.5 Unit mA V V V K V IOUT Short Circuit Current 30 80 mA 2 IL6840 AC CHARACTERISTICS Symbol Parameter Output Frequencies fH1 fH2 fH Range max fH Range min fL Sweep Frequency Test Conditions VCC = 26 V, R1 = 14 K VSCR = 0 V V SCR = 6 V VCC = 26 V, R1 = 1.7 K, VSCR = 0 V VCC = 26 V, R1 = 27 K, VSCR = 6.0 V VCC = 26 V, C1 = 100 nF 7.0 Guaranteed Limits Min 1960 1420 14 0.11 13.0 Max 2570 1840 Unit fH1 fH2 Hz Hz KHz KHz Hz TEST AND APPLICATION CIRCUIT Figure1 : Single output applied pin#5 1 F, 250V AC TIP C2 2.2 K R2 10K 8 6 5 Piezo 4 0.22 F 10K TEL C3 10 F 7 1 IL6840 2 3 VOUT 1300:8 RING C1 100nF VS R1 14K f1 = 3.22 *104 / R1 (K); f2 = 5/7 f1; fsweep = 1000 / C1(nF) 3 IL6840 Figure2 : Single output applied pin#6 1 F, 250V AC TIP C2 2.2 K R2 10K 8 6 5 Piezo 4 0.22 F 10K TEL C3 10 F 7 1 IL6840 2 3 VOUT 1300:8 RING C1 100nF VS R1 14K f1 = 3.22 *104 / R1 (K); f2 = 5/7 f1; fsweep = 1000 / C1(nF) DESCRIPTION The IL6840 tone ringer derives its power supply by rectifying the AC ringing signal. It uses this power to activate two tone generators. The two tone frequencies generated are switched by internal oscillator in a fast sequence and made audible across an output amplifier in the loudspeaker; both tone frequencies and the switching frequency can be externally adjusted. The device can drive either directly a piezo ceramic converter (buzzer) or small loudspeaker. In case of using a loud-speaker, a transformer is needed. An internal shunt voltage regulator provides DC voltage to the output stage, low frequency oscillator, and high frequency oscillator. To protect the IC from telephone line transients, a zener Diode is included. 4 IL6840 N SUFFIX PLASTIC DIP (MS - 001BA) A 8 5 B 1 4 Dimension, mm Symbol A B MIN 8.51 6.10 MAX 10.16 7.11 5.33 0.36 1.14 2.54 7.62 0 2.92 7.62 0.20 0.38 10 3.81 8.26 0.36 0.56 1.78 F L C D C -T- SEATING PLANE F G M H J N G D 0.25 (0.010) M T K H J K L M N NOTES: 1. Dimensions "A", "B" do not include mold flash or protrusions. Maximum mold flash or protrusions 0.25 mm (0.010) per side. D SUFFIX SOIC (MS - 012AA) Dimension, mm 5 A 8 Symbol A B P MIN 4.80 3.80 1.35 0.33 0.40 1.27 5.72 0 0.10 0.19 5.80 0.25 MAX 5.00 4.00 1.75 0.51 1.27 H B C 1 G 4 C R x 45 D F -TD 0.25 (0.010) M T C M K SEATING PLANE G J F M H J K M P R 8 0.25 0.25 6.20 0.50 NOTES: 1. Dimensions A and B do not include mold flash or protrusion. 2. Maximum mold flash or protrusion 0.15 mm (0.006) per side for A; for B 0.25 mm (0.010) per side. 5 |
Price & Availability of IL6840N
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |